Servo Mounts & Arms

BVM Brand Flush Wing Servo Mounts . 1 Pair Per Package.

JMP 0-Flex Servo Mount . Designed for turbine aircraft with their low vibration environment and high demand for control system accuracy. Machined from 6061-T6 aircraft aluminum with nylon mounting spacers. For JR-8411 servos. Works in any application where precision is a must. .

SECRAFT Precision Machined Heavy Duty Aluminium 6061-T6 (anodized) 1" Servo Arm for Hitec. Designed to clamp around the servo shaft and compensate for inconsistancies in the output shaft sizes. . Half arms are measured from the servo screw hole to the outside hole. Hitec: 24T(blue). Length :1.0inch(25.4mm). Fixing screw bolt is #4-40. Weight: 3.5g. 1 Per package. . Installation Guide. - Follow aircraft manufactures recommendation for Servo control horn set up. - LockTite all servo screws. - Install ball link on bottom of servo arm (where possible). - Keep all linkage tight. Note: SECRAFT servo arms should fit snug, and not just slip onto the output shaft. In fact they should go on about a 1/3 of the way with light pressure and use the screw to pull them down the rest of the way. We do this because we are all after the tightest linkage and if there is any play in the spline fit it will only get worse. If need be, place a drop of light oil in the servo arm hole being very careful not to get any oil in the servo screw hole to help get the arm in place. Remember oil in the servo screw hole will not let the Loctite work properly. We suggest the arm's be installed outside the aircraft and on a stable flat surface. .

Micro Servo Arm XL-EFLRS75/FUT/HRC (6).

Spektrum Heavy Duty Aluminum Servo Arms are the perfect companion to your Spektrum outfitted model.

SWB Double-Loc Servo Arm 4" Offset Hitec. Absolutely the finest arms on the market. Designed to clamp around the servo shaft and compensate for inconsistancies in the output shaft sizes. All arms are Heavy duty Red Anodized Aluminum and have tapping for 4/40 hardware.. . Full arms are measured from the servo screw hole to the outside hole, 2X Example” 1-1/4 Full arms are 2-1/2” from outside hole to outside hole. Offset arms are designed to be used with a rudder horn of that length and crossing the wires Example: 3” offset arm is to be used with a 3” rudder horn. Note: SWB's servo arms should fit snug, and not just slip onto the output shaft. In fact they should go on about a 1/3 of the way with light pressure and use the screw to pull them down the rest of the way. We do this because we are all after the tightest linkage and if there is any play in the spline fit it will only get worse. If need be, place a drop of light oil in the servo arm hole being very careful not to get any oil in the servo screw hole to help get the arm in place. Remember oil in the servo screw hole will not let the Loctite work properly. We suggest the arm's be installed outside the aircraft and on a stable flat surface. .

SECRAFT V3 Hitec 1" Servo Arm M3 - Blue.

Heavy Duty Composite Servo Arms ~ JRLONG. .

Heavy-Duty 1/2 Servo Arm Short: FUT. . .

SWB Double-Loc Servo Arm. -Hitec Half Arm 1"

Spektrum Heavy Duty Aluminum Servo Arms are the perfect companion to your Spektrum outfitted model.

Hitec Aluminum Servo Arms Made for Clevis - 1"

SECRAFT Precision Machined Heavy Duty Aluminium 6061-T6 (anodized) Servo Arm for Hitec.. . Half arms are measured from the servo screw hole to the outside hole. Material: aluminium 6061-T6 (anodized). . JR:23T(gold), Hitec:24T(blue), Futaba:25T(red). Length :1.0inch(25.4mm). Fixing screw bolt is M2. weight: 2.0g. 1 Per package. Bolt is not included. . Installation Guide. . - Follow aircraft manufactures recommendation for Servo control horn set up. . - LockTite all servo screws. . - Install ball link on bottom of servo arm (where possible). . - Keep all linkage tight. . - Servo arms longer than what is recommended can cause. . - The Hitec 8XXX series servos must use Futaba type. Note: SECRAFT servo arms should fit snug, and not just slip onto the output shaft. In fact they should go on about a 1/3 of the way with light pressure and use the screw to pull them down the rest of the way. We do this because we are all after the tightest linkage and if there is any play in the spline fit it will only get worse. If need be, place a drop of light oil in the servo arm hole being very careful not to get any oil in the servo screw hole to help get the arm in place. Remember oil in the servo screw hole will not let the Loctite work properly. We suggest the arm's be installed outside the aircraft and on a stable flat surface. .

Material: aluminium 6061-T6 (anodized). JR:23T(gold), Hitec:24T(blue), Futaba:25T(red). Length :1.5inch(38mm). Fixing screw bolt is M3 or #4-40. weight: 5g. 1 Per package. Bolt is not included. Installation Guide:. - Follow aircraft manufactures recommendation for Servo control horn set up. - LockTite all servo screws. - Install ball link on bottom of servo arm (where possible). - Keep all linkage tight. - Servo arms longer than what is recommended can cause. - The Hitec 8XXX series servos must use Futaba type.

SECRAFT Side Servo Mount V2. .