LIGHTS

4W PURE light, short - WHITE. Universal STROBE light for installation behind existing glass cap, mostly on wingtips or on the leading edge or special DIY solutions. The module is being delivered completely prewired on an aluminium heatsink. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. In delivery state, these lamps are only suitable for normal operation from 5 to 10 minutes when paying attention to a slight air flow. Please check operation temperatures after installation and ensure sufficient air cooling. . Technical Data:. Electricity: 4W reference power, 8(12)V, 0.35A. Beam angle: ~160°. Light intensity: ~50 Lumen RED. Light intensity: ~70 Lumen GREEN. Light intensity: ~100 Lumen WHITE. Dimension bolt : D7x15mm. Dimension chip: D8mm. Weight: 2g (without cable). Delivery: ready to use with 1m connection cable and series resistor for 2S, resistor for 3S enclosed, mounting screws. The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating. Note: The LED lights are extremely bright! Never look directly into a LED!.

UniLight DUAL NAV+STROBE, 15Wx2 - Green/White.

4W position light, 11mm - RED. Budget position / navigation light of 11mm series is externally very slim design and fits optically to smaller models. The profile-shaped polycarbonate cap is plugged on delivery. This can be painted separately. The luminaire is fully assembled for use with 2S LiPo (about 8V). During operation with 3S (12V) of the enclosed resistor must be used as an alternative you can also use a 4W-3S adapter cable. Please note that high power LEDs can be very hot, up to 70 ° C is quite normal. These luminaires with heatsink enclosures are suitable for continuous operation, when an air flow is possible (in flight). If this is not the case, then switched-on durations of 5-10 should not be exceeded. Check after installation the operating temperatures. . Technical Specifications. Electrical: 4W reference power, 8 (12) V, 0.35A. Angle:> 160 °. Aperture: 50 Lumen RED. Aperture: 80 Lumen GREEN. Aperture: 100 lumens WHITE. Dimensional light cap: 11.5x42.5x10mm until 4mm sunk without loss of the radiation angle. Overall dimensions: 11.5x70x35mm. Weight: 8g (without cable). Delivery: enclosed with 1m silicone cable and pre-assembled ready for 2S resistor operation and resistance for 3S. The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating. Note: The LED lights are extremely bright! Never look directly into a LED!.

4W PURE light, short - RED. Universal STROBE light for installation behind existing glass cap, mostly on wingtips or on the leading edge or special DIY solutions. The module is being delivered completely prewired on an aluminium heatsink. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. In delivery state, these lamps are only suitable for normal operation from 5 to 10 minutes when paying attention to a slight air flow. Please check operation temperatures after installation and ensure sufficient air cooling. . Technical Data:. Electricity: 4W reference power, 8(12)V, 0.35A. Beam angle: ~160°. Light intensity: ~50 Lumen RED. Light intensity: ~70 Lumen GREEN. Light intensity: ~100 Lumen WHITE. Dimension bolt : D7x15mm. Dimension chip: D8mm. Weight: 2g (without cable). Delivery: ready to use with 1m connection cable and series resistor for 2S, resistor for 3S enclosed, mounting screws. The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating. Note: The LED lights are extremely bright! Never look directly into a LED!.

10mm PIN navigation light 40x2W, T-Fuse - White

4W Position Light, 8mm - White. Miniature high-performance light with 4W reference power for smaller models, on tail fins or and thin wings. The mini luminaire is delivered as a ready assembled unit on a CNC manufactured aluminium heatsink and an enclosed polycarbonate cap as covering. The cap is especially designed to scatter light for better visibility. It has to be glued on during installation. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. Please check operation temperatures after installation. . Technical Data. Electricity: 4W reference power, 8(12)V, 0.35A. Beam angle: >160°. Light intensity: ~50 Lumen RED. Light intensity: ~80 Lumen GREEN. Light intensity: ~100 Lumen WHITE. Dimension cooling pin: D7x29. Weight: 4g (without cable). Delivery: ready to use with 1m silicon cable and ready made series resistor for 2S, resistor for 3S enclosed. . The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating. Note: The LED lights are extremely bright! Never look directly into a LED!.

6Wx2 Strobe, 7mm - WHITE. Miniature strobe light in triple-chip configuration extremly powerfull, externally very slim and fits optically onto smallest models with big scale factors. The profiled polycarbonate cap is delivered simply attached. It can be varnished separately, is highly transparent and unbreakable. The assembly of the lamp is astonishingly easy: with a simple surface mount, all you need is drill a 7mm hole. In this way, the luminaire can be also mounted on smaller wing tips or fuselage. The cap must be glued after the final assembly. The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be added. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heatsink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Please check operation temperatures after installation. . Technical Data:. Electricity: 6Wx2 reference power, 8(12)V, 0.45A. Beam angle: >150°. Light intensity: ~150 Lumen ROT. Light intensity: ~240 Lumen GRÜN. Light intensity: ~330 Lumen WEISS. Dimension: 19x8x6. Dimension cooling pin: D7x30. Weight: 4g (without cable). Delivery: ready to use with 0.5m PTFE cable and ready made series resistor for 2S, resistor for 3S enclosed. The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating. Note: The LED lights are extremely bright! Never look directly into a LED!.

8Wx2 universal STROBE, 10mm, T-Fuse RED. High power light with 8Wx2 reference power and wide radiation angle. The light is delivered with several radiation caps for individual usage:. 1x 10mm ROUND. 1x 10mm PROFILE EXTENSION. 1x 11mm PROFILE. 1x 15mm ROUND. 1x 24mm ROUND. 1x 24mm PROFILE. The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be used. Alternatively you can use a 8W-3S adaption cable. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These 8W luminaires are not suitable for continuous operation without additional cooling, operation times of a few minutes are possible. Please check operation temperatures. The luminaires are perfectly suited to be BEACON or ACL lights. The integrated temperature sensor will switch off the light in case of overheating. . Technical Data. Electricity: 8W reference power, 8(12)V, 0.7A. Beam angle: >160°. Light intensity: ~200 Lumen RED. Light intensity: ~400 Lumen WHITE. Dimension: 24x20x20mm. Weight: 5g (without cable). Delivery: ready to use with 1m silicon cable and series resistor for 2S, resistor for 3S enclosed. The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating. Note: The LED lights are extremely bright! Never look directly into a LED!.

Powerful position and flash light in a housing.

UniLight 5mm Navigation & Strobe, 10Wx2 - GREEN/WHITE. . Extremely slim but powerful miniature position and flashlight in one housing. The 5mm lightbar outside very slim and fits optically on kleinse models, thin airfoil and Eigent Perfect for all sports models. but by the new LED emitter has an extremely light and flash output despite the micro-dimension and is therefore also suitable for larger models. The novel, shifted inward cooling surface allows astonishingly compact dimensions with unique slim design. The luminaire is fully assembled for use with 2S Lipo (about 8V). During operation with 3S (12V) of the supplied resistor must be used. Please note that high power LEDs can be very hot, up to 70 ° C is quite normal. These lamps with heatsink enclosures are suitable for model aircraft operation when an air flow is possible (in flight). If this is not the case, then switched-on durations of 5-10 should not be exceeded. Check after installation the operating temperatures. . Technical specifications. . The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating. Note: The LED lights are extremely bright! Never look directly into a LED!.

8Wx2 Flashlight, 11mm, SHORT, T-Fuse - RED. Powerful flashlight in x2 Technology - doubled luminous power but the same waste heat! The profile light of the 11mm series is slim outside and fit optically also onto smaller models. Because of the x2-Technology, the light has an enormous luminous power and thus it's an eye-catcher even for bigger models. In delivery state, the profiled polycarbonate cap is simply attached. It can be varnished separately. It's highly transparent and unbreakable. If desired, you can recess the luminaire up to 4mm or grind down the cap, thus achieving an even smaller construction. The cap must be glued after the final assembly. Additional cooling surfaces have been waived in order to enable an extremely flat and compact assembly, especially on fuselages or wingtips. Hence, this luminaire is exclusively suitable for flash mode or short blink operation. In order to ensure operational reliability of luminaire and model, an overtemperature protection is on the underside of the item. If the luminaire is operated for too long and thus becoming too hot, this button switches off the light. In order to increase the life span, do not use this function permanently!. The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be used. Alternatively you can use a 4W-3S adaption cable. Please check operation temperatures after installation. . Technical Data. Electricity: 8Wx2 reference power, 8(12)V, 0.7A. Beam angle: >160°. Light intensity: 2x80 Lumen RED. Light intensity: 2x200 Lumen WHITE. Dimension light cap: 11.5x42.5x10mm, up to 4mm lowerable without loss of beam angle. Total mass: 11.5x42.5x10mm. Weight: 5g (without cable). Delivery: ready to use with 1m silicon cable and series resistor for 2S, resisitor for 3S enclosed . With the X2 technique high power LEDs are operated in a "cluster". These achieve double the light output for the same heat or the same light output at half heat dissipation. Yet our X2 lights are still fully compatible with all our other lamps. If X2 lights, such as spotlights, are supplied with separate cables, these cables must be used in the delivered wiring! X2 lights are reacting more strongly on a weakening battery. . The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. . Pay always attention to the operating temperature, we do not assume any warranty in case of overheating. . Note: The LED lights are extremely bright! Never look directly into a LED!.

Lens for Spotlights, 40mm

8Wx2 Strobelight / Flashlight Utra-Power, 8mm - WHITE. Miniature high-performance light with 8Wx2 Ultra-Power. Extreme performance as flaslight on tail fins or thin wings. The mini luminaire is delivered as a ready assembled unit on a CNC manufactured aluminium heatsink and an enclosed polycarbonate cap as covering. The cap is especially designed to scatter light for better visibility. It has to be glued on during installation. Please note that these Ultra-Power lights do not include a temperature protection. Please also note that high-performance LEDs can get very hot, up to 70°C is quite normal. Please check operation temperatures after installation. . Technical Data. Electricity: 8Wx2 reference power, 8(12)V, 0.7A. Beam angle: >160°. Light intensity: ~200 Lumen RED. Light intensity: ~400 Lumen WHITE. Dimension cap: 8x18x9. Dimension cooling pin: D7x29. Weight: 4g (without cable). Delivery: ready to use with 1m silicon cable and ready made series resistor for 2S, resistor for 3S enclosed. . The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating. Note: The LED lights are extremely bright! Never look directly into a LED!.