UniLight 7mm PRO Navigation Light, 1.5Wx2, FLAT – Kopie RED

$23.00

-

UniLight 7mm PRO Navigation Light, 1.5Wx2, FLAT – Kopie RED. Miniature navigation light with new COB chip generation, very small but powerfull like standard lights, fits optically onto smallest models with big scale factors. The profiled polycarbonate cap is delivered simply attached. It can be varnished separately, is highly transparent and unbreakable. The assembly of the lamp is astonishingly easy: with a simple surface mount, all you need is drill a 7mm hole. In this way, the luminaire can be also mounted on smaller wing tips or fuselage. The cap must be glued after the final assembly. The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be added. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heatsink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Please check operation temperatures after installation. . Technical Data:. Electricity: 2Wx2 reference power, 8(12)V, 0.17A. Beam angle: >150°. Light intensity: ~50 Lumen ROT. Light intensity: ~80 Lumen GRÜN. Light intensity: ~110 Lumen WEISS. Dimension: 19x8x6. Dimension cooling pin: D7x30. Weight: 4g (without cable). Delivery: ready to use with 0.5m PTFE cable and ready made series resistor for 2S, resistor for 3S enclosed. The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology. Pay always attention to the operating temperature, we do not assume any warranty in case of overheating. Note: The LED lights are extremely bright! Never look directly into a LED!.

3 in stock

SKU: UNL-PRO7020X2R Category:

Description

UniLight 7mm PRO Navigation Light, 1.5Wx2, FLAT – Kopie RED

Miniature navigation light with new COB chip generation, very small but powerfull like standard lights, fits optically onto smallest models with big scale factors.

The profiled polycarbonate cap is delivered simply attached. It can be varnished separately, is highly transparent and unbreakable. The assembly of the lamp is astonishingly easy: with a simple surface mount, all you need is drill a 7mm hole. In this way, the luminaire can be also mounted on smaller wing tips or fuselage. The cap must be glued after the final assembly.

The luminaire is ready to use for operation with 2S LiPo (ca. 8V). With 3S (12V), the enclosed resistor has to be added. Please note that high-performance LEDs can get very hot, up to 70°C is quite normal. These lamps with heatsink cases are suitable for continuous operation if an air flow (during flight) is possible. If this is not the case, the duty cycle of 5-10 minutes should not be exceeded. Please check operation temperatures after installation.

Technical Data:

Electricity: 2Wx2 reference power, 8(12)V, 0.17A
Beam angle: >120°
Light intensity: ~30 Lumen RED
Light intensity: ~60  Lumen GREEN
Light intensity: ~110 Lumen WHITE
Dimension: 19x8x6
Dimension cooling pin: D7x30
Weight: 4g (without cable)
Delivery: ready to use with 0.5m PTFE cable and ready made series resistor for 2S, resistor for 3S enclosed

The reference power is a comparison value between our offered lights. It normally refers to an operating voltage of 12V/3S Lipo and is dependent on bulbs, operating mode and technology.

Pay always attention to the operating temperature, we do not assume any warranty in case of overheating.

Note: The LED lights are extremely bright! Never look directly into a LED!

Additional information

Weight 0.01 lbs

Brand

UNILIGHT

There are no reviews yet.

Be the first to review “UniLight 7mm PRO Navigation Light, 1.5Wx2, FLAT – Kopie RED”