UniLight Nightfly Blade DIY Set for Medium size (up to 2m) Model

$130.00

-

Unilight DIY set for most models with up to 2 meters span. The set consists of two wing blades for the wings and a tail balde for the tail and rear fuselage. There are no mounting plates included. Optionally there is the safety connection set NIGHT-M-CONRG. Note: Does not include wiring, battery or controller module. Light Fixtures Only . MEDIUM DIY set, up to 2m. The set consists of two wing wings for the wings and a tail for the rear and rear fuselage. There are no mounting plates included. Optionally there is the safety connection set NIGHT-M-CONRG. uniLIGHT nightblades:. Assembly and operation:. First, the enclosed, small contact plate is glued firmly in the edge of the wings, sides or the elevator, preferably with good epoxy resin and optional battlements. Make sure that the lettering on the contact plates is readable so that the polarity is correct. In the plan view is always plus. The connection cable is guided centrally within the surface to the fuselage. All Night Blades can simply be operated in parallel on a 2S LiPo battery or on a uniLIGHT light control. Pay attention to the permissible current load and sufficient battery capacity, a shutdown at deep discharge could be deadly at night!. For commissioning, the Night Blade is simply placed on the mounting plate with the two screws and tightened, the electrical contact is made automatically. Make sure the labels are always readable. The reflector surfaces are bent once, so that as much of the light emission as possible is directed towards the model. ATTENTION: The reflector surfaces harden and can only be bent a few times. Secure the adhesive surface before you align the surfaces by hand or with a small pair of pliers to prevent breakage of the splice. After the flight the Night Blades can simply be unscrewed and easily transported. There is no trace left of the night flight system. Technical specifications:. . .

1 in stock

SKU: UNL-NIGHT-MDYISET Category:
UNILIGHT

Description

Unilight DIY set for most models with up to 2 meters span. The set consists of two wing blades for the wings and a tail balde for the tail and rear fuselage.

There are no mounting plates included. Optionally there is the safety connection set NIGHT-M-CONRG.

Note: Does not include wiring, battery or controller module. Light Fixtures Only.

MEDIUM DIY set, up to 2m

The set consists of two wing wings for the wings and a tail for the rear and rear fuselage.

There are no mounting plates included. Optionally there is the safety connection set NIGHT-M-CONRG.

uniLIGHT nightblades:

  • Compact size with maximum performance
  • Lowest influence on flight behavior
  • New cable and plugless installation
  • Optimized, adjustable cooling reflector
  • Reduced self-glare
  • 5 sizes for all standards
  • especially for wings and symmetrical for the tail unit
  • Asymmetrical design for maximum robustness
  • Safety holder with position light available
  • large systems as cable and autonomous battery version

Assembly and operation:

First, the enclosed, small contact plate is glued firmly in the edge of the wings, sides or the elevator, preferably with good epoxy resin and optional battlements. Make sure that the lettering on the contact plates is readable so that the polarity is correct. In the plan view is always plus.
The connection cable is guided centrally within the surface to the fuselage. All Night Blades can simply be operated in parallel on a 2S LiPo battery or on a uniLIGHT light control. Pay attention to the permissible current load and sufficient battery capacity, a shutdown at deep discharge could be deadly at night!
For commissioning, the Night Blade is simply placed on the mounting plate with the two screws and tightened, the electrical contact is made automatically. Make sure the labels are always readable.
The reflector surfaces are bent once, so that as much of the light emission as possible is directed towards the model. ATTENTION: The reflector surfaces harden and can only be bent a few times. Secure the adhesive surface before you align the surfaces by hand or with a small pair of pliers to prevent breakage of the splice.
After the flight the Night Blades can simply be unscrewed and easily transported. There is no trace left of the night flight system.

Technical specifications:

  • Construction: 1.5mm fiberglass carrier
  • Electric: 8V, 1.4A / 0.65A
  • Light intensity: ~ 900/550 lumens WHITE
  • Overall dimensions: 210x57mm and 150x36mm
  • Weight: 2x28g, 1x12g
  • Delivery: ready for immediate use on 2S LiPo and uniLIGHT lighting control

 

Additional information

Weight 1 lbs

Brand

UNILIGHT

There are no reviews yet.

Be the first to review “UniLight Nightfly Blade DIY Set for Medium size (up to 2m) Model”

Related products